Parkzone Corsair

man no offense but your using 8 amps off the power supply , ditch all that crap and hook the 8 amps straight to the plates , youll produce way way more . all that is a waste

You need to ditch the baking soda. It degrades into NaOH anyway eventually. But the carbon will coat your plates and keep the catalytic layer from forming through conditioning which optimizes your production and greatly improves the quality of the HHO or Hydroxy gas. See Patrick Kelly’s Chapter 10 pdf.

The Herz was variable but with in the audible range. I didn’t use one set frequency. For the most part it was an in efficient water heater at best. I am now using technologies developed by Bob Boyce. I is a Tesla type systems. That is all I can say about that period.

Pete, what is the Hz reaching the plates and what it the Amp and volt going to the plates. There have been a lot of people working on the resonant frequency of water. What are you using? What is working best for you?

hey, ive been working on a transformer driver using 3 npn transistors (2 being an inverter) and setup a CT xfmr with Q1-Pos-Q2/3 arrangement. it works fine with only one leg hooked up, but when both are running, the voltage drops considerably but on an oscope it shows both an up & down pulse (sorta)

I was wondering if you would share your Jk flip flop circuit with me as to better understand using a jk instead of transistors. i will be using either a Pic or a 555 circuit for the freq control.

Keep it up that is what is all about, never give up.

cont. Bob Boyce quote: “Even though it uses windings, it is designed for its capacitively fluxing potential, not fluxing magnetic fields….Try to think of it as a 3 phase fluxing capacitor instead of a 3 phase transformer.” Boyce and Meyers used very similar methods from what I can tell with these toroids. The charge “holding” might be the back EMF in the primaries influencing the secondaries.

Check out older texts which have been digitized by google such as AE Dolbear’s, Matter, Ether, and motion. Particle physics may be a side tangent or a subset view of physical phenomena created by top down control over academia. Bob Boyce recently mentioned on a forum:”This is NOT an electromagnetic transformer, nor was it designed to be. It is designed for switched transitions of potential (voltage) only, and passing those transitions along to modulate another dipole of higher potential.” cont.

no I wish they were but that is way more work than I’m willing to do.

Furthermore, He was using a unipolar pulse train, pulses that increased in amplitude before the off duty cycle. By starting at a low amp., This orients the H2 and O atoms, then increases power until it’s just enough to fracture the molecule, then an off cycle before current leakage occurs. But, what do I really know? I’m just a high school drop out.

He also claimed to be using a coil to create a electrical resonance between the circuit and the water capacitor, creating a standing wave of energy as well as resonating the h2o molecule increasing efficiency. We know energy takes time to dissipate. I think what we call ‘over unity’ is using resonance to keep the Pe in the system before dissipation. That’s how people win SPL competitions, one note boxes tuned to a vehicle Fc and at of distance of a 1/4 waveL.

Try experimenting with different freqs if you tx can take it. I’ve also found at certain frequencies when I added any electrolyte I lost production and skyrocketed my amp draw. I’ve got great results with 396 cycles and other random freq up to 20k. Electrons behave like waves. What I gathered from numerous patents of Meyers, he said the torroid held a charge and released it during the off duty cycle, so he got two pulses for the price of one.

are the secondaries wound first and then the primaries wound over the secondaries in this?

I’m jealous of your homemade power supply. What state did you attend high school in? Was it a private school and what years? The quality of education continues to go down the gutter every year. Thanks for the video!

It has been the case that many great inventions have occurred by those willing to experiment and learn the positive and negatives of their work. Seldom is success accomplished before many failed first attempts.
Although, your project is not very efficient at producing H, I applaud your efforts to experiment and learn. Continue working and learning from your efforts and dont listen to those who criticize your efforts You may enjoy learning more about Tesla and his experimentation.

you need to throw that in the trash and start over….you think thats hho good production?…thats not enough to even play with

You need stage 3 hho production or you are wasting your time:
/watch?v=AmYHEnXBguI

You need stage 3 hho production or you are wasting your time:

Free 90v, 200ma, 15watts
/watch?v=Kdup42Epq0o

I hope you are not planning on keeping your crimped copper wire connection so close to the reaction.
Copper will corode and eventually you will get a spark and one heck of a startle LOL.

Also you may want to consider seling the unit so you get less current leakage and higher production.
Zero Fossil Fuel explains this in his and demonstartes it as well.

Nice little unit all in all.

Keep up the good work.

Hi,
I am in the process of building a HHO Gen.
I need to find some parts. I need a ferrite toroid coil core 3.50 x 2.00 x .500. Do you know where I can get one? I also need 550ft. heavey build teflon coated copper magnetic wire 23AWG.
Can you help on that also?
I’m not very good with electronics. But I am a do it yourself person.
Jim

The output seems too small. Try this :

Array of 6 , 1/16″ apart, Perform dry isolation test with multi-meter, configure +-+-+-. 12-14VDC 17-20A.

It should perform like a scalded monkey!

have you tried it with tap water?

Can you explain in more detail and or demonstrate what you are explaining?

inductors on pos and neg. about 100 turns 22 swg magnet wire around a ferrite core. no elyte is needed once the plates are conditioned.